Butterfly Valve Body Castings Relief Valve Casting Valve Parts Casting Foundry

Material: Carbon (1.6220)

Standard: DIN EN 10213

Casting process:  alkaline phenolic resins

Weight: 280KGS

Size:14~ 36 inches

Description

Butterfly valve body castings relief valve casting valve parts casting foundry description 

Material: Carbon (1.6220)

Standard: DIN EN 10213

Casting process:  alkaline phenolic resins

Weight: 280KGS

Size:14~ 36 inches

Heat treatment method: NBK

Surface treatments:  shot blasting and polishing

Chemical Composition:

C:0.19  

Si:0.31

Mn:1.2  

S:0.008

P:0.015

Mechanical property:

Tensile strength: 560MPa

Yield strength: 385MPa

Elongation: 26%

Export countries: Netherlands, Australia, Germany, Japan.

Our advantage products: all kinds of Valve castings

 

Technical key points:

Ø hot sections of valve plate casting during pouring are very concentrated, do not place the risers dispersedly, big risers must be placed at the top of two-axis holes for feeding, and exhaust risers be placed far away from the main risers.

Ø Put cold iron blocks at the hot sections at the bottom of valve plate, it can help the risers solidify in sequence to enhance the risers’ feeling effect, at the same time, increase production rate and reduce casting cost.

Ø In the premise of ensuring a large cross-sectional area, a reduced and steady flow rate, no spray of molten steel which may caused secondary oxidation, the runner should be as thin as possible to reduce the suction area of the runner. The thickness of the inner runner should be less than 0.7 times of the wall thickness of the casting, and the width of the runner should be more then 4 times of the thickness, which is more favorable for the slagging and cleaning of the molten steel.

 

TECHNOLOGY ADVANTAGES 

Ø We are a innovation-driven company, we have five patents and another 13 patents will be expected to get in short months.

Ø we are willing to develop all new material only if it’s required in application.

Ø Advantage technology in composition control, especially super low carton steel, stainless steel and duplex stainless steel.

Ø We cast very good surface of thin-wall castings, which is normally not easy to control for sand castings, but we made suitable technology and are able to guarantee smooth no-defect surface.

Ø Crack is fatal flaw for pressure resistant container. We can make sure no crack inside and outside of the pump and valve castings, and a good pressure-resistant performance.

Ø All our technology innovation only for one aim--- the best quality, even that means a higher cost and lower production rate.

 车间67.jpg


OUR SERVICE

Ø We provide free technical service about casting parts and application issues.

Ø Free on-site touring and introduction of our factory

Ø We provide process design and validation for free

Ø We can guarantee on-time delivery of samples and goods

Ø Close follow-up of all orders by special person and keep customers informed timely

Ø All after-sale request will be responded in 24 hours

 案例19.jpg

FAQ

1. Can you produce OEM parts according to our casting drawing and machining drawing?

  A: Yes, we can produce OEM parts according to our casting drawing and machining drawing.  

2. What is the delivery time of pattern, casting parts and machining finished parts?

  A: In general, pattern making time is 20-40 days base on the design of the parts, sample making time is 20-30 days, machining finished parts lead time is 40-60 days. The lead time will vary base one different design and weight of the parts, please contact us for details.

3. What kinds of physical and chemical testing you can provide?

  A: The physical and chemical testing we provide include:

     Ø chemical composition testing

     Ø physical property testing:hardness test,Tensile performance testing, room temperature impact testing, low temperature impact test

     Ø NDT: PT, MT, UT &RT

     Ø Metallographic testing

4. What’s the maximum weight of castings you can produce?

  A: The maximum weight of castings we can produce is 1.8 tons.

5. Which kinds of NDT methods that your company can provide?

  A: The NDT we provide are PT, MT, UT and RT.

6. Can you guarantee the traceability of your products?

  A: Regular products: On-site inspection record and FG Test report will be kept more than 3 years

Important products:On-site inspection record and FG Test report will be kept more than 5 years , applying processing card system, and make sure one card for each piece, thus to keep each piece of products are traceable.

 

Please feel free to contact with us for detailed information, we will reply you at once.


Contact us:

Wuxi Lingtong Casting Co.,Ltd.

Attn: Ms. Vivian Wang

Email: vivian@ltzz.com

Tel: +86 510 85990876  

Cell: +86 13861777146 15852600207

Wechat:+86 15852600207

Skype: Vivian_wlh

Web: www.pump-casting.com


Feedback

Products List
Contact Us

Tel: +8613861777146
+8615852600207
Fax: 86-510-85992265
E-mail: Vivian@ltzz.com